( 31% OFF )
  • Graphic1
  • Graphic1

Lee Star Juice Extractor LE-827

2,499.00

  • Stainless steel full size juicer mesh for extra durability and better juicing
  • Front knob control 3+ pulse speed setting
  • Pulp collection in one place for easy disposal
  • Easy checking of the pulp with see-through unbreakable transparent lid
  • Smooth and easy to clean

Check Availability At

Pincode field should not be empty!
Buy Now
SKU: LE-827 Category:

PRODUCT DETAILS

  • Stainless steel full size juicer mesh for extra durability and better juicing
  • Front knob control 3+ pulse speed setting
  • Pulp collection in one place for easy disposal
  • Easy checking of the pulp with see-through unbreakable transparent lid
  • Smooth and easy to clean

TECHNICAL SPECIFCATIONS

Power Supply                                     :                   220-230V AC 50Hz
Power                                                  :                   500 Watts
Motor Type                                        :                    Universal
Material  (Basic unit )                       :                    A.B.S Plastic
Speed  Control                                   :                   3 Speed with Pulse
 Rating                                                 :                   30 Minutes (3min.On 2min.Off)
 Motor Speed (R.P.M)                      :                   18000 (Approx)- No Load
                                                                       *Subject to change without prior notice

 

 

 

 

USING THE JUICER

  • Mount the juicer body on the basic unit
  • Place the juicer mesh into the juicer body. Ensure that the mesh sits properly and locks the lower coupler of the basic unit .If necessary push down slightly or rotate the mesh a little. Don’t apply any undue pressure. The mesh is a very fine and precisely balanced component.
  • Push the juicer spout (outlet) cover in position and press.
  • Mount the juicer cover onto the juicer body and lock the clamps, plug the cord in and the juicer is ready for use. Press the switch marked pulse to check if the filter mesh assembly is properly seated with the lower coupler of the basic unit. The mesh should spin evenly without wobbling. Wash ingredients and cut suitably to fit feeder opening.
  • Place a glass under the spout. Set switch to position”1”
  • Push ingredients into the feeder with the food pusher.

OVERLOAD PROTECTION

To protect the motor from burning, in case of overload, the appliance is fitted with an automatic overload protector under the base of the basic unit. If the motor stops it is an indication of excess load switch off the unit, take out excess material . Wait for 2/3 minutes and press the overload protection plunger .Then restart the unit.

 

Note:- Overload protection plunger is to be pressed to restart only after 2/3 minutes.

 

STEPS TO SAFETY

  • Do not allow children to handle the machine.
  • Keep the machine away from direct heat and sunlight, at a suitable height on a flat surface for easy operation.
  • While operating run the machine in short cycle of 30-90 seconds as per requirement, do not run it for a long duration.
  • Clean the mesh with a soft nylon brush. Do not use any metallic object or knife etc.
  • Do not run the machine empty.
  • Do not overload the machine.
  • In case of smoke or smell put off the machine.

WARRANTY

This Lee Star Mixer Grinder is fully warranted against any defect arising out of defective materials or faulty workmanship for a period one year on product & two years on motor from the date of purchase. Should any defect develop in this product, the customer should bring the product to the nearest authorized service provider, where the company undertakes to get the product repaired.

 

This warranty is not valid if:

  • The use and care instructions have not been followed.• Defects are caused by accident, misuse, abuse or commercial use or damage in transit• Plastic parts are not covered under this warranty •The repair work is carried out by persons not authorized by the company •Any modification or alteration of any nature is made in the product •Normal wear & tear of the product is not covered under warranty• The Bill/Cash memo and copy of warranty card is not presented •Under no circumstances, whether based on limited warranty or otherwise shall the company be liable for incidental, special or consequential damages. •Use of product indicates acceptance by you of the aforesaid terms and conditions.